Woodworking InformationHow to Strip Wood Furniture

Now I'm about to demonstrate how to strip
a finish off of a piece of furniture. It's a bit echoey in here, but that's because we're
in the spray room, which sucks all the air towards this filter, keeping all the dust,
the particles of paint thinner and paint, any kind of floating materials that can be
in the air, going in one direction to keep the dust off the piece and to keep it safe
in the room, to breathe. Other precautions are, a respirator, gloves, and safety glasses.
The things we'll be using to do this process are paint thinner, paint remover, a wire brush,
steel wool, sandpaper, and some rags. This piece of furniture has flaking finish.

In
places it's completely worn out. In other places you have dirty build-up. We're going
to remove all that. The first thing we'll attack is the flaky paint, 'cause that's the
loosest, and the easiest thing to remove.

We'll do that using a wire brush, being careful
not to mar up the wood. When you're using a wire brush of any sort on anything flaky,
it's best to wear safety glasses and a respirator. Once you've used your wire brush to remove
any loose paint, then it's time to go to the next step. What we'll go to next is these
areas where the stain is still fairly well-attached, but it's worn away in the surrounding area.
This will be the next easiest thing to remove.

After you're done wire brushing the chair,
use some compressed air to blow any dust off of the chair. The next step is to remove any
actual build-up that's not able to be removed with the wire brush. We're going to be using
two things. We're start using paint thinner, and then if we need something stronger, we'll
use some of this paint remover.

I just tried using paint thinner with a rag. That didn't
seem to be enough, so I stepped it up to the steel wool. That also doesn't seem to be enough,
so now I'm going to try using this paint remover, which is a much stronger solvent. If there
seem to be areas that the paint remover and the paint thinner both will not remove due
to deeper staining, then you might need to take..Get a little more aggressive and use
something like a cabinet scraper to scrape back areas.

And then, reveal a little more
fresh wood. For demonstration purposes, I'm going to go ahead and stop here, but when
you're working on yours at home, just keep doing the same process all over the entire
chair until you get results that seem to appear to be like this..

Woodworking InformationHow to Bend Wood to Make Furniture

Next I will be demonstrating how to bend wood.
This particular type of bend is called a bent lamination where you use multiple layers bent
around a form with glue in between, clamp down, when the glue dries, it retains its
shape. The first step is making your bending form. This particular bending form is made
out of three layers of three quarter inch MDF. First you cut your outside radius or
any shape that you want to bend to, then you cut an inside radius small enough to where
your clamps that you'll be using can reach over your form and over your piece that you
will be bending, clamping it down firmly.

The first step after building your bending
form is to now rip your strips. When ripping strips, you need to be aware that your strips
can be pulled down into your table saw through your throat plate. Replace your throat plate
with a zero clearance throat plate. Now it's time to rip the strips.

The first step of
ripping strips is to set the gage on the rip fence to the closest one eighth of an inch
mark that cuts the least amount of material off your wood as possible. Once again, the
first step is to set the rip fence gage to the closest one eighth of an inch increment
that cuts the least amount off your wood. Now we'll make that pass shaving off the edge
of the board. We will be creating one eighth of an inch strips.

The way you do this is
moving the rip fence gage one quarter of an inch each time. What that allows for, it allows
for the one eighth of an inch thickness of the saw blade plus gives you the one eighth
of an inch strip being sawed off the outside, which is the most safest and efficient way.
This process gives you nice, bendable, one eighth of an inch strips that if you follow
the method, it will give you each one will be very consistent. Repeat this method until
you have as many strips as you need. The next part of this process is the glue up.

You need
to make sure that you have all your things right around you because you only have a limited
amount of time to do a glue up like this because of how many glue seams you have. I've got
a roller for applying glue to the strips, all my clamps, and my bending form right here
where I need them. Now you need to take your roller, applying glue in the tray, roll glue
onto your strips. All you have to do is roll it onto the first one, have your stack in
front of you, roll a light amount of glue onto each strip flipping them onto each other
and continue this process until you've covered each strip with glue and have them evenly
stacked.

Next after the glue up is clamping all of your strips to your form. Whenever
possible, it's best to use a pad. In this case you're using small scraps of MDF to act
as a buffer between the clamp and your first strip. The reason for doing this is the amount
of pressure that the clamps can create can make marks or dent your wood, and then sometimes
if there's any glue on the surfaces, it can react with the steel leaving dark marks on
your wood.

First is find the center of the strips, place it on your form and get your
first clamp in place. Once you've done this, lay down, lay the form down along with the
clamp and your strips down flat. Repeat this process until you've reached both ends of
your strips. Bent laminations need to dry for approximately eight hours.

Once enough
time has passed, you want to un-clamp your form. If everything went right, you should
get a nice, consistent curve, the shape of your form..

Weekly Hebrew Words with Yaara - Furniture

Want to speak real Hebrew from your first lesson? Sign up for your free lifetime account at HebrewPod101.Com. Hi, everyone! My name is Yaara and this is Hebrew Weekly Words. Im really glad you joined us because the theme this week I think is really useful and its Furniture. So lets start!
(Shulkhan) table    .
(Kulam yoshvim misaviv la'shulkhan.) Everybody is sitting around the table.


(Kise) chair      .
(Ha'kise haze kaved yoter mishehu nir-eh.) This chair is heavier than it seems.  
(Madaf sfarim) "bookshelf    .
(Yesh meakhorai madaf sfarim.) There's a bookshelf behind me. See.
(Mita) "bed    .
(Ha'mita sheli raka meod.) My bed is really soft.


(Sapa) sofa Thats an easy one because its a bit similar, isnt it?
(Sapa) sofa        ?
(Ata yakhol la-azor li liskhov et ha'sapa hazot?) Can you help me carry this sofa? Thank you! Thats very nice of you. This is the end. Thank you so much for watching and well see you next week on Hebrew Weekly Words. Oh and dont forget to check out the site.

Bye!.

This Guy Is Making Furniture and Buildings out of Your TrashNat Geo Live

- [Arthur] I hate plastic. That's why we've engulfed
on a 15 year mission to turn that into something
that we actually want. We have collected
around 750 new materials that's coming from our
daily post-consumer waste. It can go into any
consumer product at lower cost,
higher performance.

First of all, let
me show of hand who actually recycled
something today? Wow. Okay, this is a weird audience. But guess what, guess what? There's actually, in
the United States, we have the lowest
recycling rate of all the developed nations. It's plateauing at
34% recycling rate.

You look at the waste
here, it has tires, apparel waste, on top of
plastic bags and PET bottles. I think this is one
of a big problem here, no one actually wants
to be responsible for all that waste
that we're creating. We are responsible,
all of us here, are responsible for this mess. Our solution is, we
have to make trash sexy.

And this what National
Geographic is so good about. For us engineers, that
is engineering porn. Okay, so, why is that? Because this is the highest
performance animal in the ocean. It's the fastest,
it has the scale that's optimized for
speed, and it's just the pure physical
form is no waste.

Zero waste. Everything is considered,
everything is designed. But this is what we get,
every grain of rice, every wheat, every bread
that you eat has 20% waste. Fiber waste.

Every PET bottle, all
of these are perfectly nontoxic material that can
constantly be recycled, reused. And then we have
a growing e-waste. Electronic waste. Huge amount of it, it
has precious metals, it has a lot of toxic elements.

Let me get nerdy a
little bit here, okay? Why we are not turning
that into product, today, if you touch your
clothes there's no
recycled content in it. There's the seat
you're sitting on, the environment that we're in, has no recycled content in it. This is a problem. Why? Why not? The reason is because
the polymer chain got broken in the
recycling process.

Then how do you make
then strong again? If you're a weak animal, a
weak animal cannot be sexy. Maybe they are but, you
know they're not very sexy. So we are actually
drawn to pretty things. So how do you make
that sexy again? We have to use fiber
to bridge in-between.

And this is a, we
go back to history, the Romans built
cement aqueducts, Chinese built walls, all with agricultural
waste grinded down into these powder forms
they mix into the cement. What it does is, it has
silicon dioxide in it, amorphous silicon dioxide. It's a natural glue. It's actually forming
these broken polymer chains if you mix into it, it actually
starts to come together, conglomerates, into much
much stronger materials.

The ancient does it, why
aren't we doing that today? So that's one of
the solutions how we reinforce material
using organic waste. So why aren't we doing this? Toxicity. This is a piece of leather, and that's a piece of recycled
PET fabric on the side. Just look at how many steps
that's required to produce and process a piece
of leather fabric versus a piece of
recycled PET waste.

Every step requires a carbon
footprint, energy, chemicals. On the recycled PET
side, you only use water, heat, and knife to
cut the pieces down. Why aren't we doing this more? We invent seven new
materials a month, we have collected
around 750 new materials that's coming from our
daily post-consumer waste. But the problem is no one
wants to buy them, okay? So we have to pioneer
making up new applications.

So I'll show you very
quickly what we did. This is what we call
molecular cooking. Molecular cooking at all levels. Molecular gastronomy
at the marketing front, new pioneering, engineering, and designing, and
marketing fronts.

It can go into any
consumer product at lower cost,
higher performance. We have built 40
story tower with trash, campuses, nine story
tall building, museum, we just finished the biggest
e-waste recycling plant where we turn the
waste of a waste into all the
building's structure. We've worked on a food waste
recycling plant in Taiwan, and we are also
doing a car waste recycling plant that's
finishing this year. This looks like a
piece of marble.

It's not. It's right here. It's a piece
of recycled PET non-woven, no chemical added, heat
pressed, structural material, and it's also an air purifier. Okay, made from cigarette
waste, which is tobacco, which I smoked for many years.

Okay, it can be formed, shaped, into a lot of different formats, we turned it into this
in Milan this year. This is a pavilion,
it's actually inspired by the natural lung molecule. And that's actually
capturing formaldehyde in the air and it's
integrated with electronics. It's all interlocked,
single material, no glue, and I want you to focus
on the waste of the waste of that cigarette butt
production process, which are those chairs.

We actually turned that
into this furniture product using the
cigarette butts. So the product's called
"Anything Butt," okay? And this process allows
other designers globally to do even more different
types of furniture products. Please, this has to
look sexy to you now, because this is the leftover of a typical German
beer festival. Look at all that material
that's out there.

This is a possibility here. And we turn that, all
that crap, e-waste, food waste, recycled Nike
shoes, into recycled Nike store. In New York, you can go see, in Paris, Le Marais,
you can go see, in Milan, in London,
you can see all these stores that are
made from apparel waste and e-waste, and
any type of waste. We scale across 23 countries, taking portable
manufacturing machinery into developed world, because we want
to keep the trash in the developed world,
not to ship to India, China, Taiwan, anywhere else.

Thank you..

Soft Clear Wax Recipe for Chalk Paint & Furniture- 2 Ingredients $3 TO MAKE!

Hii I'm Wendi with Nashville Restoration
and today we're going to make some clear wax to use with chalk paint.  You need 1/4
of cup of white beeswax pellets and you need a cup of either baby oil or mineral
oil.  You also need a mason jar with a lid. So just to put your
beeswax and baby oil in your mason jar.

It's got to be a mason jar because other
jars you cannot put in boiling water so make sure it's a mason jar.  Put it on the
stove and fill the water so it's just a half inch below the level of the wax or
else your jar will float up put the top. Put your stove on a medium high heat and stand by. You are going to stir it every couple minutes.

Just to get it mixed up and it
is done when the wax pellets disappear and it looks like this. It is  pretty much
clear when it's done. You can let it cool in the pan but if
you want to do it more quickly which I. Usually do, just carefully remove it from
the pan.

It is hot oil and it's very dangerous so do it with a great deal of
caution and use some pot holders. Now you are ready to cool it. Put some ice water in a pan and once again add water just below the level of the oil. You're just going to stir this every few minutes until it starts to turn
cloudy like a cloudy white.

When it looks like this, after about ten minutes of stirring every couple of minutes, take it out of the ice water and put the
lid on and shake it up. You're gonna come back and shake it up for thirty seconds every five minutes or so until it has reached room temperature.
Once it's room temperature it will stay like this it will look like this and
that is your clear wax. This looks pretty much exactly like the clear wax that I
have purchased from some name-brand companies and I can't tell the
difference when I use it. It brushes right on just like the other
waxes do that are commercially prepared.

I came up with this recipe doing
some research trying to figure out what was in clear wax and these were the two
most common ingredients so I skipped any additives and just went with these two ingredients and the shaking it up is really important. That's what keeps it blended.
If you don't shake it up it's gonna you kind of separate. I wanted to show you what it looks like on furniture. So this is just a basic white table.

I'm
gonna brush it on just like any other clear wax. I don't use a wax brush I use
this type of brush. It is  a $6 brush and I can't tell the difference in the
brushes.  I mean after you brush it on  and you're still going to come back and
wipe it down and then if you're distressing you're gonna sand so to me
if you like the brush you're using and the wax goes on then that's the brush
you should use.

So as you do with any wax, you wipe the wax down after you put it
on there. If you're distressing this is when you would distress when the wax is
still fresh on there. It's a lot easier to distress then waiting for the wax to
actually dry and set up. So I did some of this distressing off-camera because I'm going to break out the electric sander because hand sanding the top is pretty
intense.

So this is what it looks like afterwards. This is my clear wax results. I'm
completely happy with it. I've been painting for many years both houses and
furniture and I think this works great.

So thank you for watching. Please check
back for more videos don't forget to subscribe and if you have a video you
would like to see, send me a message. I also put up videos all the time so
please check back for new stuff. Thank you!  .

Silver Metallic Furniture Painting DIY Princess Chair Makeover!

DIY Silver Paint Victorian Chair Makeover For this project you will need some
oil-based silver paint. I am using "Liquid Leaf" and it is available at craft and
hobby stores and you can also order it online. I'm using oil-based paint so that
I don't have to strip and sand before I. Paint the chair.

I'm using a one-inch
artist brush and you can either be ready to throw your brush away or get some
mineral spirits to clean your brush with when you're done. Make sure you shake up your paint really well before you start. I'm taping the edges of the fabric with
painters tape because you will not get the paint cleaned off the fabric if you
get it on there so tape it as close up to the edges as you can. I cover the
rest of the chair with fabric kind of as I go to keep drips from getting onto the
fabric.

This paint goes on very easily and it also dries very fast. I paint in
the direction of the grain only because that gives it a more natural look. I also
use for this entire chair only two of the small containers  of paint that I showed in the beginning of the video When you get close to the edges where the fabric is,
just go really slow and try to not even get any paint on the tape and if you do
that, you're less likely to have the paint seep under the tape. Just get your paint on enough to cover
and be sure you don't leave any drips behind.

One of the hardest places to keep
paint off the fabric is down where the arms or the back of the chair meet the
fabric so be especially careful taping that off that you are all the way up to
the edge between the wood and the fabric. I usually add a couple extra rows
of tape because if I don't I will probably either drip paint on the fabric
or rub my brush against the fabric as I. Go. To paint the chair you want to keep a
minimal amount of paint on your brush when you do this.

You want to stay
away from the tape as much as possible. Just try to use a little bit of paint and
do a light coat and don't try to jam your brush down next to the tape because
it will probably seep through onto the fabric.   The reason I'm using the oil-based paint
is so that I don't have to sand this wood all the way down or prime it before
I put this paint on there. The only reason my wood looks like this
is because I tried a different metallic paint that I did not like so I had to
remove most of that chalky finish to put this finish on there.

The other reason I like
an oil-based paint for this chair is that when I go to distress it I can go
ahead and distress it and I do not have to put a coating over top of it like a
clear wax or polyurethane. Once it's distressed it's ready to go. You could
also just leave it silver if you didn't want to distress it. So this is a pretty
quick and easy way to do this chair.

I let my paint dry for eight hours before
I came back to distress it. The best sandpaper to use when distressing this
is going to be between 180 to a 220 grit. It will take the finish off fairly
easy so just go slow so you can see what you're doing and learn exactly what the
sandpaper is going to do. Because this is an oil-based paint it actually has
undertones in the silver so what happens is when you sand it is that it looks kind of like sterling silver.

It brings out some grays and some blacks which are  colors from which this paint was made. As much as I like chalk paint I
have found that the best metallic finish is in an oil-based paint and that is why
I am using that on this chair. I tried a metallic chalk paint before this and it
just did not have the kind of shine you can get from an oil-based paint. Now like
I said I am NOT going to put a top coat on this, If you wanted to you could put
an oil-based polyurethane on it but I.

Don't see a reason to because you've
already got a well protected shiny finish and you just don't have
do that.   I'm doing most of my sanding just on the
edges and then I kind of run the sandpaper down the middle of the grooves as I go, -it's pretty quick and painless to get this chair distressed with this
paint so probably about 10 to 15 minutes of sanding on this chair and it is done.
I always sand with the grain because it gives it a more natural look and then
like on the bottom of this leg, I go around the other way because that's just
how it would be naturally. So these are my results. This is my sterling silver distressed Victorian chair makeover.

I'm really happy with it I think it looks
great. I love the paint and I love the colors. So thank you for watching please
check back I put up new videos all the time and I have all types of DIY videos for furniture, dressers, upholstery and
some DIY home repair stuff. Thanks for watching! You.

Second-Hand FurnitureBudget Home Tour

Hello guys, my name is Tegan and today I
want to show you our secondhand furniture, which is basically all of our
furniture. There are several reasons why my husband like to further by secondhand
furniture rather than brand new. Number one you save money. Secondhand is always cheaper than brand new.
Number two, you can buy more unique pieces.

Not necessarily one-of-a-kind
antiques but furniture that says something about you rather than when you shop.
Number three you can afford higher quality, solid rather than ply-board
pieces. This third point is what we really try to focus more on nowadays. So,
quality over quantity in all aspects of life I guess.
And number four, you reduce
landfill by buying less into consumer culture.
Our shoe cabinet is actually a
wine cabinet.

I saw this idea on pinterest and I bloody loved it! I grew
up never wearing shoes inside the house so there must always be somewhere to
store shoes at the door. You can find wine cabinets much cheaper than this but
I took a long time to find something that would fit in this awkward space for
our front entrance and now that is one of my favorite pieces of furniture.
It's very solid and I think it's probably the highest quality piece we own. We brought it home hanging out the boot of a car! I thought i was going
to lose it on the freeway but you gotta do what you gotta do!
This plant stand was
$12 at a trash and treasure market. I had literally been looking for one like it
for years but athefew I'd come across were always more than $100.

When
I bought it and was carrying it around the market, one lady accosted me and
seemed to be very upset that I'd found at first. She was like, "where did you get
that?!" "What are you gonna do with it?!"
And I was like,
"I'm gonna put a plant in it?" I swear she nearly ripped it out of my
hands This entertainment unit was probably a
little more than i originally wanted to pay, but we really love the design. All we
had to do was drill a hole in the back for the DVD player and the appletv
chords. And it's got plenty of room for all our
DVDs, our cds and a few other bits and pieces as well.


We have pretty much decided that we are never ever going to buy a new couch or lounge suite again, so
long as we have our cat Selene. The only piece of furniture we've bought
brand-new was a Fantastic Furniture couch, it wasn't amazing quality but it
looked alright and it did the job. Then Selene arrived on the scene and she
thought it belonged to her. I tried everything to stop her scratching it;
wrapping it up in tin foil and sticky tape, buying her all the different kinds cat
scratchers but she basically destroyed it within 18 months.

We purchased this
leather suite for a great price and around the same time I invested in the
cheapest cardboard cat scratchers from Kmart which Selene loves! We don't expect it to stay in pristine condition forever because Selene does still like to sleep
on them but at only $250, we don't really mind so much
This rug, while not secondhand,
was ex-floor stock which is another great thing to look for
instead of buying brand new. Before I met Adi, I planned to keep a Jungle Python as a pet. I arranged for my wildlife keeper license and I bought
this converted kitchen cabinet from eBay as a terrarium. Then almost immediately
after that I met Adi and he flipped out when he saw the, what i thought was an
obviously fake snake, so it's been empty ever since.

I don't really want to get
rid of it. We use it for book storage and I keep my
records in here as well. We've thought about keeping frogs or stick-insects in
here but I'm not so keen. I'm not sure really how I feel about keeping a snake
in such a captive environment anymore either.

This is the second dining table we've
bought a couple. When we first moved in together we used my old IKEA desk as a dining table for months.
Then we bought
a small round 4 seater on ebay and once we moved into this house we sold
that one to someone who was going to refurbish it, because we want to tell me
bigger for this space honestly I think we paid a little too
much for it, especially since it's just from Fantastic Furniture but it has been
serving us very well. I searched for ebay for our master bed suite for
months and eventually won the bidding on this one for what I think was a great
price.

It's natural, solid oak and I love the paneling on the side of the drawers.
The model came with wooden handles for all the drawers but the previous owners
never installed them and we think it looks great without them too!
We were a bit disappointed with this purchase, it's a fantastic furniture brand again
and while I knew this when we bought it the photos did not indicate the poor
condition of the wood and I couldn't leave it there because I'd already
organized for my father to bring his ute up to the city to help us collect it. It has however been very useful when
family come to stay. And finally, not really a furniture item i guess but a
large household piece nonetheless Our aquarium which is way too expensive for us to buy brand new. This was another 'hanging out the boot on the freeway'
scenario which in hindsight was not the smartest idea.

But it survived and even
though we've only had varying success with the aqua garden and not very much
success with fish, I think it's a great addition to our
home. Not just with the peaceful vibe it creates but the cupboards below act as
bonus extra storage too. Thanks for watching guys, let me know if you enjoyed
this video and whether or not you buy secondhand furniture and, if so, what is
your favorite piece?
See you next time Bye!.